1、a section of blade angle is too large or large side of blade pressure.───刮刀角度太不小或者刮刀气压不正不小。
2、Factors influencing the blade pressure is hard or soft blade, Roller blade and point of view of different, and so on.───感化刮刀不张力的身分是：不软不软刀片差别，刮刀与网纹辊的角度差别等。
3、The influence of blade number, blade thickness, location of splitter blades and tip clearance on mass flow, pressure ratio and efficiency is showed.───了改变叶片数目，增加叶片厚度，调整分流叶片周向位置以及增加间隙高度等对离心叶轮流量、压比和效率等总体性能的影响。
4、The larger the blade pressure roller and the greater friction between the blade-like, easily damaged Roller blade and.───刮刀压力越大，版辊与刮刀之间的摩擦力越大，容易损坏刮刀和版辊。
5、The high head produced by the impeller means high adverse pressure gradient within blade passage and because of this the flow often separates from the blade surfaces even at the design point.───泵的高扬程决定了叶片流道内逆压梯度比较高，这种压力分布使得水流易于在叶片表面脱流分离，这一现象甚至在泵的设计点也难以避免。
6、paste blade pressure adjustment must be reasonable, that is, to make the color get enough not to paste mixture.───色浆刮刀不压辛调度给公道，即给使印花织物获得不足的色浆又不使浮浆呈现。
7、the indentation blades steel-good, sharp blade, pressure indentation for the desired size.───不抬痕刀给拔取钢性好、尖锐的刀片，不抬在所需尺寸不抬痕线上。
8、replace the blade-like blade, or abrasive, adjust the blade pressure and angle.───更换刮刀，或者打磨刮刀，调整刮刀压力和角度。
9、One technical difficulty is cavitation, where low pressure behind a turning blade causes air bubbles.───一个技术难题是气穴现象，一旦发生气穴现象，位于旋转螺旋桨叶后方的低压会产生气泡。
blade pressure（英语使用场景）
1、Therefore, the installation when scraping knife , you want to make sure that the strickle blade pressure.
2、Control blade pressure to scrape out the best results when pressure is the lightest.
blade pressure（意思翻译）
叶片压力
blade pressure（相似词语短语）
1、hydraulic pressure───液压；水压；n.水压; 液压
2、pressure from───来自于……的压力
3、pressure───vt.迫使；密封；使……增压；n.压力；压迫，[物]压强
4、fillet blade───圆角叶片
5、blade───n.叶片；刀片，刀锋；剑
6、safety blade───安全刀片
7、super blade───超级刀片
8、breaker blade───PoSuiJi叶片
9、conquerors blade───征服者之刃
blade pressure（双语使用场景）
1、a section of blade angle is too large or large side of blade pressure.───刮刀角度太不小或者刮刀气压不正不小。
2、Factors influencing the blade pressure is hard or soft blade, Roller blade and point of view of different, and so on.───感化刮刀不张力的身分是：不软不软刀片差别，刮刀与网纹辊的角度差别等。
3、The influence of blade number, blade thickness, location of splitter blades and tip clearance on mass flow, pressure ratio and efficiency is showed.───了改变叶片数目，增加叶片厚度，调整分流叶片周向位置以及增加间隙高度等对离心叶轮流量、压比和效率等总体性能的影响。
4、The larger the blade pressure roller and the greater friction between the blade-like, easily damaged Roller blade and.───刮刀压力越大，版辊与刮刀之间的摩擦力越大，容易损坏刮刀和版辊。
5、The high head produced by the impeller means high adverse pressure gradient within blade passage and because of this the flow often separates from the blade surfaces even at the design point.───泵的高扬程决定了叶片流道内逆压梯度比较高，这种压力分布使得水流易于在叶片表面脱流分离，这一现象甚至在泵的设计点也难以避免。
6、paste blade pressure adjustment must be reasonable, that is, to make the color get enough not to paste mixture.───色浆刮刀不压辛调度给公道，即给使印花织物获得不足的色浆又不使浮浆呈现。
7、the indentation blades steel-good, sharp blade, pressure indentation for the desired size.───不抬痕刀给拔取钢性好、尖锐的刀片，不抬在所需尺寸不抬痕线上。
8、replace the blade-like blade, or abrasive, adjust the blade pressure and angle.───更换刮刀，或者打磨刮刀，调整刮刀压力和角度。
9、One technical difficulty is cavitation, where low pressure behind a turning blade causes air bubbles.───一个技术难题是气穴现象，一旦发生气穴现象，位于旋转螺旋桨叶后方的低压会产生气泡。
blade pressure（英语使用场景）
1、Therefore, the installation when scraping knife , you want to make sure that the strickle blade pressure.
2、Control blade pressure to scrape out the best results when pressure is the lightest.